Home » Electrical » Power Factor Meters » Altek 134-2 Milliamp Calibrator
Altek 134-2 Milliamp Calibrator
Part Number:
ALTK 134-2
In Stock?
Stock may be available
please call (877)766-5412 to confirm
please call (877)766-5412 to confirm
Quantity
Price:
$534.00 
USD (change)
USD (change) 
The Altek 134-2 Pocketcal Milliamp Calibrator will check, calibrate and measure all your current signal instruments in a 4 to 20 milliamp DC loop. Use at every point in your loop. Source & Read 0.00 to 24.00 mA, Simulate a Two-Wire Transmitter or use the Altek 134-2 Pocketcal to simultaneously Power & Measure your Two-Wire
Transmitters. Toggle the display to show milliamps or percent of 4 to 20.
Calibrate recorders, digital indicators, stroke valves or any other instruments that get their input from a 4 to 20 mA loop. Easily set any value to within 0.01 mA with the
speed sensitive digital potentiometer.
The “QUIK-CHEK” pushbuttons provide rapid checking of 4.00, 20.00 and a third point between 0.00 to 24.00 mA.
Check loop wiring and receivers by using the Altek 134-2 in place of a 2-Wire transmitter. Simulate a changing process input to check loop response and control settings. The Altek 134-2 Pocketcal Milliamp Calibrator uses any loop power from 3 to 45V DC.
Check controller outputs or measure the milliamp signal anywhere in the loop. The Model 134-2 measures 0.00 to 24.00 mA signals with much greater accuracy than
a typical multimeter. Toggle the display to show milliamps or percent of 4 to 20.
Simultaneously measure the output of a 2-Wire Transmitter while using the internal batteries to supply up to 14V DC to power the transmitter. Handy for checking
transmitters in the field or on the bench.
What's Included:
Transmitters. Toggle the display to show milliamps or percent of 4 to 20.
Calibrate recorders, digital indicators, stroke valves or any other instruments that get their input from a 4 to 20 mA loop. Easily set any value to within 0.01 mA with the
speed sensitive digital potentiometer.
The “QUIK-CHEK” pushbuttons provide rapid checking of 4.00, 20.00 and a third point between 0.00 to 24.00 mA.
Check loop wiring and receivers by using the Altek 134-2 in place of a 2-Wire transmitter. Simulate a changing process input to check loop response and control settings. The Altek 134-2 Pocketcal Milliamp Calibrator uses any loop power from 3 to 45V DC.
Check controller outputs or measure the milliamp signal anywhere in the loop. The Model 134-2 measures 0.00 to 24.00 mA signals with much greater accuracy than
a typical multimeter. Toggle the display to show milliamps or percent of 4 to 20.
Simultaneously measure the output of a 2-Wire Transmitter while using the internal batteries to supply up to 14V DC to power the transmitter. Handy for checking
transmitters in the field or on the bench.
What's Included:
- Attached test leads with alligator clips
- Data Sheet on 134-2
- Manufacturer's Statement of Calibration Practices
- Three Year Warranty
The Good:
The Bad:
The Bottom Line:
The Bad:
The Bottom Line:
Full Review
- Basic Milliamp Functions — Source 0.00 to 24.00 mA or -25.0 to 125.0%, read mA or percent to 24.00 mA, simulate 2-wire transmitters, power and measure 2-wire transmitters.
- Basic Accuracy — ±( 0.08% of 24 mA Span + 1 LSD)-Source to read within 0.03 mA.
- Quik-Chek Outputs — HI and LO push-buttons for instant output of 20.00 or 4.00 mA. Speed sensitive digital potentiometer adjusts output from any QUIK-CHEK position for valve stroking.
- Power Up Transmitters — Drives to 700 ohms loads.
- Long Battery Life — Sources 12 mA for over 22 hours, 20 mA for over 16 hours. Turns itself off after 30 minutes.
- Dependable Operation — Fuseless protection to 120 V AC/DC.
Product brochures
No user reviews available.
