Home » DV Power RMO200 High DC Current Resistance MicroOhmMeter
DV Power RMO200 High DC Current Resistance MicroOhmMeter
RMO200 is a micro-ohmmeter based on state of the art technology, using the most advanced switch mode technique available today. RMO200 generates true DC current with automatically regulated test ramps. During the test RMO200 ramps with increasing current before measuring and decreasing current after the measurement. This eliminates magnetic transients.
After the test current has been set, the automatic test procedure is started by pressing the Ω-button. The test result is displayed as R=U/I. There is enough memory in RMO200 to store 100 measurements. All measurements are time and date stamped. They can also be exported to a PC with RMO-Win software. The software connects a PC to RMO200 with a RS232 cable. The RMO-Win makes it easy to report and analyse all results.
The set is equipped with thermal and overcurrent protection. RMO200 has very high ability to cancel electrostatic and electromagnetic interference in high HV electric fields. It is achieved by very efficient filtration. The filtration is made utilizing appropriate hardware and software.
Output Ratings
The full output is available from the RMO200 at 230V Mains Supply. A reduced output is available from lower supply voltages.
Supply Voltage Output Current Full Load Voltage
230 V AC 200 A DC 6,0 V DC
115 V AC 200 A DC 6,0 V DC
Output current is filtered and has a ripple of less then 1%.
The RMO200 output is rated at 200 A for 2 minutes and 100 A continuously at 25°C ambient.
CONT Mode
RMO200 can generate DC current continuously using the CONT menu. In this menu the current can be chosen the same way like in the SINGLE menu, but the duration of the test can be preset. The test is started pressing the Ω-button. During the test, a new result is shown on the display each second.
Typical application is measuring resistance of:
After the test current has been set, the automatic test procedure is started by pressing the Ω-button. The test result is displayed as R=U/I. There is enough memory in RMO200 to store 100 measurements. All measurements are time and date stamped. They can also be exported to a PC with RMO-Win software. The software connects a PC to RMO200 with a RS232 cable. The RMO-Win makes it easy to report and analyse all results.
The set is equipped with thermal and overcurrent protection. RMO200 has very high ability to cancel electrostatic and electromagnetic interference in high HV electric fields. It is achieved by very efficient filtration. The filtration is made utilizing appropriate hardware and software.
Output Ratings
The full output is available from the RMO200 at 230V Mains Supply. A reduced output is available from lower supply voltages.
Supply Voltage Output Current Full Load Voltage
230 V AC 200 A DC 6,0 V DC
115 V AC 200 A DC 6,0 V DC
Output current is filtered and has a ripple of less then 1%.
The RMO200 output is rated at 200 A for 2 minutes and 100 A continuously at 25°C ambient.
CONT Mode
RMO200 can generate DC current continuously using the CONT menu. In this menu the current can be chosen the same way like in the SINGLE menu, but the duration of the test can be preset. The test is started pressing the Ω-button. During the test, a new result is shown on the display each second.
Typical application is measuring resistance of:
- high, middle and low voltage circuit breakers
- high, middle and low voltage disconnecting switches
- high-current bus bar joints
- cable splices
- welding joints
The Good:
The Bad:
The Bottom Line:
The Bad:
The Bottom Line:
Full Review
- Lightweight - only 7 kg
- Powerful - 5A-200A DC
- Measuring range 0 - 999 mΩ
- Resolution to 0,1 µΩ
- SINGLE/CONT Mode
- Mechanical protection IP54
1 Mains Power Supply
Connection according to IEC/EN60320-1; UL498, CSA 22.2
Mains supply from 90 Vto 264 V AC; 50-60 Hz
2 Output data
Test current 5 A - 200 A DC
Current duration 200 A for 5 minutes, 100 A continuously
Measuring range Resolution
0,1µΩ - 999,9µΩ 0,1 µΩ
1,000mΩ - 9,999mΩ 1 µΩ
10,00mΩ - 99,99mΩ 10 µΩ
100,0mΩ - 999,9mΩ 0,1 mΩ
Typical accuracy ±(0,2% rdg + 0,2% FS)
3 Environment conditions
Operating temperature -10°C - +50°C / 14°F - +122°F
Storage and transportation -25°C - +70°C / -13°F - +158°F
Humidity 5% - 95% relative humidity, non condensing
4 Dimensions and Weight
Dimensions 198 mm x 255 mm x 380 mm (7,8 in x 10 in x 15 in) (W x H x D) without handle
Weight 7,0 kg/15,4 lb
5 Mechanical protection IP54
6 Warranty two years
7 Safety Standards
European standards EN 61010-1
International standards IEC 61010-1
UL 3111-1
CAN/CSA-C22.2 No 1010.1-92
8 Electromagnetic Compatibility (EMC)
CE conformity EMC standard 89/336/EEC
Emission EN 50081-2, EN 61000-3-2/3
Interference Immunity EN 50082-2
Connection according to IEC/EN60320-1; UL498, CSA 22.2
Mains supply from 90 Vto 264 V AC; 50-60 Hz
2 Output data
Test current 5 A - 200 A DC
Current duration 200 A for 5 minutes, 100 A continuously
Measuring range Resolution
0,1µΩ - 999,9µΩ 0,1 µΩ
1,000mΩ - 9,999mΩ 1 µΩ
10,00mΩ - 99,99mΩ 10 µΩ
100,0mΩ - 999,9mΩ 0,1 mΩ
Typical accuracy ±(0,2% rdg + 0,2% FS)
3 Environment conditions
Operating temperature -10°C - +50°C / 14°F - +122°F
Storage and transportation -25°C - +70°C / -13°F - +158°F
Humidity 5% - 95% relative humidity, non condensing
4 Dimensions and Weight
Dimensions 198 mm x 255 mm x 380 mm (7,8 in x 10 in x 15 in) (W x H x D) without handle
Weight 7,0 kg/15,4 lb
5 Mechanical protection IP54
6 Warranty two years
7 Safety Standards
European standards EN 61010-1
International standards IEC 61010-1
UL 3111-1
CAN/CSA-C22.2 No 1010.1-92
8 Electromagnetic Compatibility (EMC)
CE conformity EMC standard 89/336/EEC
Emission EN 50081-2, EN 61000-3-2/3
Interference Immunity EN 50082-2
Product brochures
No user reviews available.
